Thread Pitch Calculator
Look up standard metric and imperial screw thread dimensions, including major, pitch, and minor diameter, by size in one free online chart. Compare coarse versus fine threads, like M8 or 3/8-16 UNC versus 3/8-24 UNF, instantly in your browser.
Major diameter
6 mm
Pitch
1 mm
Pitch diameter
5.35 mm
Minor diameter
4.917 mm
Values are basic (nominal) dimensions per ISO 68-1 / ASME B1.1 — they don't include manufacturing tolerance classes.
Usage examples
Checking pitch diameter for a go/no-go gauge
Look up the basic pitch diameter of a thread designation before comparing it against a gauge or caliper reading.
Comparing coarse vs. fine metric threads
Switch between coarse and fine pitch series for the same nominal diameter (e.g. M12) to see how pitch, pitch diameter, and minor diameter change.
Reading an imperial drawing callout
Convert a callout like "1/4-20 UNC" into its major diameter, pitch diameter, and minor diameter in decimal inches.
Sizing a clearance hole for an M8 coarse bolt
Look up M8 × 1.25 coarse to get its basic pitch diameter (7.188 mm) and minor diameter (6.647 mm) before picking a clearance or tap drill size for the mating hole.
Deciding between 3/8-16 UNC and 3/8-24 UNF for a tapped hole
Compare the pitch diameter and minor diameter of 3/8-16 UNC against 3/8-24 UNF at the same 3/8 in major diameter to judge thread engagement before choosing which series to tap.
Quick reference
Metric (M) · Coarse
| Thread | Pitch (mm) | Pitch diameter (mm) | Minor diameter (mm) |
|---|---|---|---|
| M3 × 0.5 | 0.5 | 2.675 | 2.459 |
| M4 × 0.7 | 0.7 | 3.545 | 3.242 |
| M5 × 0.8 | 0.8 | 4.48 | 4.134 |
| M6 × 1 | 1 | 5.35 | 4.917 |
| M8 × 1.25 | 1.25 | 7.188 | 6.647 |
| M10 × 1.5 | 1.5 | 9.026 | 8.376 |
| M12 × 1.75 | 1.75 | 10.863 | 10.106 |
| M14 × 2 | 2 | 12.701 | 11.835 |
| M16 × 2 | 2 | 14.701 | 13.835 |
| M18 × 2.5 | 2.5 | 16.376 | 15.294 |
| M20 × 2.5 | 2.5 | 18.376 | 17.294 |
| M22 × 2.5 | 2.5 | 20.376 | 19.294 |
| M24 × 3 | 3 | 22.051 | 20.752 |
Metric (M) · Fine
| Thread | Pitch (mm) | Pitch diameter (mm) | Minor diameter (mm) |
|---|---|---|---|
| M3 × 0.35 | 0.35 | 2.773 | 2.621 |
| M4 × 0.5 | 0.5 | 3.675 | 3.459 |
| M5 × 0.5 | 0.5 | 4.675 | 4.459 |
| M6 × 0.75 | 0.75 | 5.513 | 5.188 |
| M8 × 1 | 1 | 7.35 | 6.917 |
| M10 × 1.25 | 1.25 | 9.188 | 8.647 |
| M12 × 1.5 | 1.5 | 11.026 | 10.376 |
| M14 × 1.5 | 1.5 | 13.026 | 12.376 |
| M16 × 1.5 | 1.5 | 15.026 | 14.376 |
| M18 × 2 | 2 | 16.701 | 15.835 |
| M20 × 2 | 2 | 18.701 | 17.835 |
| M22 × 1.5 | 1.5 | 21.026 | 20.376 |
| M24 × 2 | 2 | 22.701 | 21.835 |
UNC (coarse) / UNF (fine)
| Thread | Threads per inch | Major diameter (in) | Pitch diameter (in) | Minor diameter (in) |
|---|---|---|---|---|
| #4-40 | 40 | 0.112 | 0.0958 | 0.0849 |
| #6-32 | 32 | 0.138 | 0.1177 | 0.1042 |
| #8-32 | 32 | 0.164 | 0.1437 | 0.1302 |
| #10-24 | 24 | 0.190 | 0.1629 | 0.1449 |
| 1/4-20 | 20 | 0.250 | 0.2175 | 0.1959 |
| 5/16-18 | 18 | 0.3125 | 0.2764 | 0.2524 |
| 3/8-16 | 16 | 0.375 | 0.3344 | 0.3073 |
| 7/16-14 | 14 | 0.4375 | 0.3911 | 0.3602 |
| 1/2-13 | 13 | 0.500 | 0.450 | 0.4167 |
| 5/8-11 | 11 | 0.625 | 0.566 | 0.5266 |
| 3/4-10 | 10 | 0.750 | 0.685 | 0.6417 |
| 1-8 | 8 | 1.000 | 0.9188 | 0.8647 |
| #4-48 | 48 | 0.112 | 0.0985 | 0.0894 |
| #6-40 | 40 | 0.138 | 0.1218 | 0.1109 |
| #8-36 | 36 | 0.164 | 0.146 | 0.1339 |
| #10-32 | 32 | 0.190 | 0.1697 | 0.1562 |
| 1/4-28 | 28 | 0.250 | 0.2268 | 0.2113 |
| 5/16-24 | 24 | 0.3125 | 0.2854 | 0.2674 |
| 3/8-24 | 24 | 0.375 | 0.3479 | 0.3299 |
| 7/16-20 | 20 | 0.4375 | 0.405 | 0.3834 |
| 1/2-20 | 20 | 0.500 | 0.4675 | 0.4459 |
| 5/8-18 | 18 | 0.625 | 0.5889 | 0.5649 |
| 3/4-16 | 16 | 0.750 | 0.7094 | 0.6823 |
| 1-12 | 12 | 1.000 | 0.9459 | 0.9098 |
Frequently asked questions
What do major, pitch, and minor diameter mean?
Major diameter is the largest diameter of the thread (measured at the crest for an external/bolt thread). Pitch diameter is the diameter at which the thread groove width equals half the pitch — it's the key dimension used for thread fit. Minor diameter is the smallest diameter, measured at the root of the thread.
What standard do these values follow?
Metric threads follow ISO 262 for the pitch series (coarse and fine) and ISO 68-1 for the 60° basic thread profile used to derive pitch and minor diameter. Imperial UNC/UNF threads follow ASME B1.1, which uses the same 60° profile geometry.
Why don't these numbers match my caliper measurement exactly?
These are basic (theoretical) dimensions, not a specific tolerance class. Real bolts and nuts are cut to a tolerance class (e.g. 6g/6H) that allows for clearance and manufacturing variation, so actual measured diameters will be slightly smaller (external) or larger (internal) than the basic values shown here.
What's the difference between coarse and fine metric threads?
Coarse pitch is the standard, most commonly used series for a given diameter and is specified by default when a drawing just says "M12" with no pitch. Fine pitch threads have a smaller pitch for the same major diameter, giving a larger pitch diameter, more thread engagement per unit length, and better resistance to loosening under vibration, at the cost of being slower to cut and more sensitive to cross-threading.
Does this cover every thread standard?
No, only the most common sizes are included (metric M3–M24 coarse and fine, and common UNC/UNF imperial designations). Specialty threads or pipe threads (like NPT) aren't covered — consult a dedicated reference for those.
How do pitch and TPI relate to each other?
They're reciprocals expressed in different units: pitch (mm/thread) is the axial distance from one thread crest to the next, while TPI (threads per inch) counts how many crests fit in one inch. Converting between the two just needs TPI = 25.4 / pitch(mm), or pitch(mm) = 25.4 / TPI. For example, 20 TPI corresponds to a pitch of 1.27 mm — close to, but not the same as, the M6 metric coarse pitch of 1.0 mm, which is why metric and imperial fasteners of similar diameter are rarely interchangeable.
Does the minor diameter shown here apply to both bolts and nuts?
The minor diameter calculated here follows the internal-thread (nut) convention, which is also the value most general-purpose thread charts label as "minor diameter." An external thread's (bolt's) actual root diameter is cut slightly smaller than this basic value to leave root clearance, while an internal thread's minor diameter (hole size before/after tapping) is meant to land close to it. If you need the external thread's designed root diameter specifically, consult a tolerance-class table rather than this basic-dimension lookup.
Can this calculator handle multi-start threads or non-60° profiles?
No. The pitch, pitch diameter, and minor diameter formulas used here assume a standard single-start, 60° V-profile thread as defined in ISO 68-1 and ASME B1.1. Multi-start threads (where lead ≠ pitch), Acme threads, buttress threads, and other non-60° profiles use different geometry and aren't covered by this tool.