Capacitor Charge Time Calculator
Calculate an RC circuit's charge and discharge time from resistance and capacitance, including the time constant (tau) and percentage charged at any elapsed time. Handy for sizing debounce circuits, timing networks, or a 555 timer's RC pair, all computed free and client-side.
Time to reach target
1 s
Time constant (τ = R×C): 1 s
63.2% Vsupply (3.1606 V)
Usage examples
Sizing a debounce or delay circuit
Find how long an RC circuit takes to charge past a logic threshold, useful for button debounce or power-on delay circuits.
Checking a timing capacitor's time constant
Calculate τ = R×C for a given resistor/capacitor pair before using it in an oscillator or filter design.
Estimating discharge time for safety
Find how long a capacitor takes to discharge to a safe voltage after power is removed.
Tuning a 555 timer's RC network
Before committing to a 555 astable or monostable design, check how long the timing capacitor takes to reach the 1/3 or 2/3 supply thresholds the 555 actually switches at.
Comparing a 10kΩ/100µF pair against a 100kΩ/10µF pair
Both combinations give the same τ = 1s, so compare charge curves for resistor/capacitor pairs that trade off resistor loading versus capacitor size while keeping timing identical.
Quick reference
Capacitor voltage after N time constants (% of supply)
| Number of time constants (τ) | Charging | Discharging |
|---|---|---|
| 0.5 τ | 39.3% | 60.7% |
| 1 τ | 63.2% | 36.8% |
| 2 τ | 86.5% | 13.5% |
| 3 τ | 95% | 5% |
| 4 τ | 98.2% | 1.8% |
| 5 τ | 99.3% | 0.7% |
Time constant (τ = R×C)
| R | 100 nF | 1 µF | 10 µF | 100 µF | 1,000 µF |
|---|---|---|---|---|---|
| 1 kΩ | 100 µs | 1 ms | 10 ms | 100 ms | 1 s |
| 10 kΩ | 1 ms | 10 ms | 100 ms | 1 s | 10 s |
| 100 kΩ | 10 ms | 100 ms | 1 s | 10 s | 100 s |
| 1 MΩ | 100 ms | 1 s | 10 s | 100 s | 1,000 s |
Time to 99.3% charge (5τ)
| R | 100 nF | 1 µF | 10 µF | 100 µF | 1,000 µF |
|---|---|---|---|---|---|
| 1 kΩ | 500 µs | 5 ms | 50 ms | 500 ms | 5 s |
| 10 kΩ | 5 ms | 50 ms | 500 ms | 5 s | 50 s |
| 100 kΩ | 50 ms | 500 ms | 5 s | 50 s | 500 s |
| 1 MΩ | 500 ms | 5 s | 50 s | 500 s | 5,000 s |
Frequently asked questions
Is my input sent to a server?
No. All calculations happen entirely in your browser and are never sent to a server.
What does '1 time constant (τ)' mean?
One time constant is the time for a charging capacitor to reach about 63.2% of the supply voltage, or for a discharging capacitor to drop to about 36.8% of its starting voltage. After about 5τ, the capacitor is considered essentially fully charged or discharged (over 99%).
Why can't I reach exactly 100%?
Exponential charge/discharge curves only approach 0% or 100% asymptotically and mathematically never reach it exactly, so the target percentage must be less than 100%.
Does this account for the capacitor's internal resistance or tolerance?
No. This is an ideal RC circuit calculation. Real capacitors have tolerance (often ±10-20%) and some leakage, so actual timing may vary somewhat from a real component.
Why does the 63.2% figure matter so much for digital logic thresholds?
It doesn't directly - logic thresholds depend on the specific chip family. A CMOS input might switch around 50% of its supply, while a Schmitt-trigger input has different high and low thresholds entirely. The 63.2%/36.8% figures only describe one specific time constant (1τ); use the percent-of-supply target mode to compute the time to any threshold your actual components require.
Does ESR (equivalent series resistance) affect the timing?
For a simple charge/discharge timing calculation, ESR adds a small additional series resistance that's usually negligible compared to the charging resistor, especially for film or ceramic capacitors. For electrolytic capacitors with higher ESR, or when R is very small, real timing can measurably deviate from the ideal R×C calculation here.
Why is my measured charge time different from what this calculator shows?
Besides capacitor tolerance and leakage, common real-world factors include the source's own output impedance (which adds to R), parasitic capacitance in the circuit and probes, and for electrolytics, dielectric absorption that makes the voltage curve deviate slightly from a pure exponential near full charge.