555 Timer Calculator
Calculate the output frequency, period, and duty cycle of a 555 timer circuit in astable or monostable mode from resistor and capacitor values. Free online tool for designing LED blinkers, clock signals, or fixed delay timers, with results updating instantly in your browser.
With this classic astable configuration, the duty cycle is always above 50% because the output stays high during charging through both R1 and R2, but low only during discharging through R2. For a lower duty cycle, a diode placed across R2 or a different topology is commonly used.
Result
6.8714 Hz
Period
145.53 ms
Duty cycle
52.38%
High time
76.23 ms
Low time
69.3 ms
Usage examples
Designing an LED blinker circuit
Pick R1, R2, and C values for a 555 astable circuit that blinks an LED at a chosen frequency and duty cycle.
Generating a clock signal for digital logic
Calculate the output frequency of a 555 astable oscillator to drive a counter or shift register.
Setting a fixed delay with a monostable 555
Find the R and C values needed to produce a single output pulse of a specific duration when triggered.
Building a 1Hz tick for a seven-segment clock
Try R1=1kΩ, R2=47kΩ, C=10µF in astable mode and check the resulting frequency against 1Hz, then adjust R2 to dial it in exactly.
Debouncing a mechanical switch with a monostable 555
Use a monostable 555 to stretch a noisy mechanical switch's bounce into one clean pulse - pick R and C so the pulse width comfortably exceeds the switch's typical bounce time of a few milliseconds.
Quick reference
Monostable (one-shot): Pulse width (t = 1.1 × R × C)
| R | 1 nF | 10 nF | 100 nF | 1 µF | 10 µF | 100 µF |
|---|---|---|---|---|---|---|
| 1 kΩ | 1.1 µs | 11 µs | 110 µs | 1.1 ms | 11 ms | 110 ms |
| 10 kΩ | 11 µs | 110 µs | 1.1 ms | 11 ms | 110 ms | 1.1 s |
| 47 kΩ | 51.7 µs | 517 µs | 5.17 ms | 51.7 ms | 517 ms | 5.17 s |
| 100 kΩ | 110 µs | 1.1 ms | 11 ms | 110 ms | 1.1 s | 11 s |
| 470 kΩ | 517 µs | 5.17 ms | 51.7 ms | 517 ms | 5.17 s | 51.7 s |
| 1 MΩ | 1.1 ms | 11 ms | 110 ms | 1.1 s | 11 s | 110 s |
Astable (oscillator): Frequency, R1 = 1 kΩ
| R2 | 1 nF | 10 nF | 100 nF | 1 µF | 10 µF | 100 µF | Duty cycle |
|---|---|---|---|---|---|---|---|
| 1 kΩ | 481 kHz | 48.1 kHz | 4.81 kHz | 481 Hz | 48.1 Hz | 4.81 Hz | 66.7% |
| 4.7 kΩ | 138.75 kHz | 13.875 kHz | 1.388 kHz | 138.75 Hz | 13.875 Hz | 1.388 Hz | 54.8% |
| 10 kΩ | 68.714 kHz | 6.871 kHz | 687.144 Hz | 68.714 Hz | 6.871 Hz | 0.687 Hz | 52.4% |
| 47 kΩ | 15.189 kHz | 1.519 kHz | 151.895 Hz | 15.189 Hz | 1.519 Hz | 0.152 Hz | 50.5% |
| 100 kΩ | 7.179 kHz | 717.911 Hz | 71.791 Hz | 7.179 Hz | 0.718 Hz | 0.072 Hz | 50.2% |
| 1 MΩ | 721.14 Hz | 72.114 Hz | 7.211 Hz | 0.721 Hz | 0.072 Hz | 0.007 Hz | 50% |
Frequently asked questions
Is my input sent to a server?
No. All calculations happen entirely in your browser and are never sent to a server.
What's the difference between astable and monostable mode?
Astable mode continuously oscillates, producing a repeating square wave - useful for clocks and blinkers. Monostable mode produces a single output pulse of a fixed length each time it's triggered - useful for delays and one-shot timing.
Why is the duty cycle always above 50%?
In the classic 555 astable circuit, the output is high while the capacitor charges through both R1 and R2, but low only while it discharges through R2. Since the charge path is always longer than or equal to the discharge path, duty cycle can't go below 50%. A diode placed across R2 is a common trick to get closer to 50% or below.
Can I use this for very high frequencies?
The formulas are accurate for the ideal case, but at very high frequencies (above a few hundred kHz) real 555 chips are affected by internal propagation delays that aren't modeled here, so actual frequency may be lower than calculated.
What supply voltage does a 555 timer need?
The classic bipolar NE555 runs from about 4.5V to 16V, while low-power CMOS variants like the TLC555 or LMC555 can run as low as 2V and draw far less supply current. The timing formulas here are independent of supply voltage, but your chosen voltage needs to be within the specific chip's rated range.
How much current can the 555's output actually drive?
A standard bipolar 555 can source or sink up to about 200mA, enough to directly drive a small LED, relay coil, or low-power buzzer. CMOS 555 variants typically have much lower output drive capability (often under 100mA), so check your specific chip's datasheet before connecting a higher-current load directly.
Why does my circuit's actual frequency drift or differ from the calculation?
Besides resistor and capacitor tolerance (a 5% resistor and 20% capacitor stack up to significant variation), electrolytic timing capacitors can drift with temperature and age, and parasitic capacitance from breadboard wiring can add to C at high frequencies. For precision timing, use low-tolerance film capacitors and metal-film resistors.