Inductor Color Code Calculator
Decode an inductor's color bands into its inductance value in microhenries (µH), supporting both 4-band and 5-band precision coding with tolerance. Free online reference for identifying axial inductors and RF chokes pulled from a parts bin, no installation required.
A gold band in position 1 or 2 is a decimal point (MIL-style coding for values under 10 µH): the other two bands are both digits and there is no multiplier. For example, red-gold-red = 2.2 µH and gold-red-red = 0.22 µH.
Result
1 mH ±5%
Tolerance range: 950 µH – 1.05 mH
Usage examples
Reading an axial inductor pulled from a parts bin
Pick the color bands you see on the inductor's body in order to get its inductance in µH and its tolerance range.
Checking a 5-band precision inductor
Switch to 5 bands to decode a three-digit-precision inductor that uses a third digit band before the multiplier.
Confirming what a black tolerance band means
Select black as the tolerance band to see the ±20% tolerance it represents — unlike resistors, inductors use an actual color for this rather than leaving the band off.
Decoding a brown-black-red-gold inductor for an RF choke
Select brown, black, red, gold to confirm a 1000µH (1mH) choke with ±5% tolerance before placing it in a power supply filter circuit.
Verifying a surplus inductor before reusing it in a build
Read the bands on a salvaged axial inductor to confirm its µH value matches what the original circuit called for, rather than guessing from its physical size alone.
Quick reference
Inductor color code chart (µH)
| Color | Digit | Multiplier | Tolerance |
|---|---|---|---|
| Black | 0 | ×1 | ±20% |
| Brown | 1 | ×10 | ±1% |
| Red | 2 | ×100 | ±2% |
| Orange | 3 | ×1,000 | – |
| Yellow | 4 | ×10,000 | – |
| Green | 5 | ×100,000 | – |
| Blue | 6 | ×1,000,000 | – |
| Violet | 7 | – | – |
| Grey | 8 | – | – |
| White | 9 | – | – |
| Gold | Decimal point (band 1 or 2) | ×0.1 | ±5% |
| Silver | – | ×0.01 | ±10% |
Common inductor values (4-band)
| Result | Bands |
|---|---|
| 0.1 µH ±5% | Brown – Black – Silver – Gold |
| 0.22 µH ±5% | Gold – Red – Red – Gold |
| 0.47 µH ±5% | Gold – Yellow – Violet – Gold |
| 1 µH ±5% | Brown – Black – Gold – Gold |
| 2.2 µH ±5% | Red – Red – Gold – Gold |
| 4.7 µH ±5% | Yellow – Violet – Gold – Gold |
| 10 µH ±5% | Brown – Black – Black – Gold |
| 15 µH ±5% | Brown – Green – Black – Gold |
| 22 µH ±5% | Red – Red – Black – Gold |
| 33 µH ±5% | Orange – Orange – Black – Gold |
| 47 µH ±5% | Yellow – Violet – Black – Gold |
| 68 µH ±5% | Blue – Grey – Black – Gold |
| 100 µH ±5% | Brown – Black – Brown – Gold |
| 220 µH ±5% | Red – Red – Brown – Gold |
| 330 µH ±5% | Orange – Orange – Brown – Gold |
| 470 µH ±5% | Yellow – Violet – Brown – Gold |
| 1 mH ±5% | Brown – Black – Red – Gold |
| 2.2 mH ±5% | Red – Red – Red – Gold |
| 4.7 mH ±5% | Yellow – Violet – Red – Gold |
| 10 mH ±5% | Brown – Black – Orange – Gold |
Frequently asked questions
Is the inductor color code the same as the resistor color code?
The digit colors (black through white, 0–9) and the power-of-ten multiplier colors are the same scheme as resistors, just read out in microhenries (µH) instead of ohms. This was verified against multiple electronics references (learnabout-electronics.org and electricaltechnology.org, cross-checked against several other sources) and found consistent. The tolerance band is where the two parts diverge — see the next question.
Why does black appear as a tolerance color here, when resistors don't use black for tolerance?
This is a genuine, verified difference from resistor convention. On resistors, a ±20% tolerance is implied by having no tolerance band at all — no color is assigned to it. On inductors, black is explicitly used as a tolerance band color meaning ±20%, alongside gold (±5%) and silver (±10%). Both the "no band" and "black band" conventions for ±20% show up across inductor references, so this tool treats black as a selectable tolerance option.
Is 4-band the standard configuration for inductors?
Yes, 4-band (two digits, one multiplier, one tolerance) is the standard EIA configuration for axial inductors, which is why it's the default here. A 5-band variant adds a third significant digit for higher precision; this tool supports both.
Does this tool send anything to a server?
No. All calculations happen entirely in your browser and nothing you enter is transmitted anywhere.
Which end do I start reading the bands from?
Start from the band closest to one end of the inductor's body, leaving a visibly wider gap before the next band on the other side. The tolerance band (gold, silver, or black) is also usually spaced slightly apart from the digit bands, which helps confirm you're reading left to right rather than right to left.
Why do some inductors have no visible color bands at all?
Many inductors, especially larger power inductors and SMD types, print their value directly as text or a numeric code instead of using color bands - color coding is mainly used on small axial (molded) inductors where printed text would be hard to read at that size.
Does the color code tell me the inductor's current rating or DC resistance?
No. The color bands only encode inductance and tolerance. Maximum current (saturation current) and DC resistance depend on the core material and wire gauge, which aren't part of the standard color code - check the manufacturer's datasheet for those specs.