Gauge to mm Converter

Convert wire gauge (AWG) and sheet metal gauge numbers to millimeters and inches instantly. Useful for reading wire spec sheets, checking steel sheet thickness, or picking the right gauge for a DIY electronics project, free online with no installation required.

Result

2.5882 mm

0.1019 in

AWG gives wire diameter; steel sheet gauge (MSG) gives plain steel sheet thickness. Galvanized steel and aluminum use different gauge tables and aren't covered here.

Usage examples

Converting an AWG number from a wire spec sheet to mm

See the actual wire diameter in mm for an AWG number printed on a component datasheet.

Finding out what gauge a sheet of steel is

Enter a thickness measured with calipers (in mm) to find the nearest standard sheet metal gauge number.

Converting a gauge callout on a foreign drawing to mm

Convert a material spec given in American gauge numbers into millimeters for a local purchase order.

Picking the right wire gauge for a DIY electronics project

Check what diameter 22 AWG or 18 AWG actually is in mm before choosing hookup wire for a soldering or wiring project.

Comparing two sheet metal gauge numbers before fabrication

Convert both 16-gauge and 20-gauge steel to millimeters to see exactly how much thicker one panel is than the other before sending a part out for fabrication.

Quick reference

AWG wire gauge

AWGmmin
00011.6840.46
0010.40490.4096
09.26580.3648
08.25150.3249
17.34810.2893
26.54370.2576
35.82730.2294
45.18940.2043
54.62130.1819
64.11540.162
73.66490.1443
83.26360.1285
92.90640.1144
102.58820.1019
112.30480.0907
122.05250.0808
131.82780.072
141.62770.0641
151.44950.0571
161.29080.0508
171.14950.0453
181.02370.0403
190.91160.0359
200.81180.032
210.72290.0285
220.64380.0253
230.57330.0226
240.51060.0201
250.45470.0179
260.40490.0159
270.36060.0142
280.32110.0126
290.28590.0113
300.25460.01
310.22680.0089
320.20190.008
330.17980.0071
340.16010.0063
350.14260.0056
360.1270.005
370.11310.0045
380.10070.004
390.08970.0035
400.07990.0031

Sheet metal gauge (MSG)

Gaugemmin
74.5540.1793
84.1760.1644
93.7970.1495
103.4160.1345
113.0380.1196
122.6570.1046
132.2780.0897
141.8970.0747
151.7090.0673
161.5190.0598
171.3670.0538
181.2140.0478
191.0620.0418
200.9120.0359
210.8360.0329
220.7590.0299
230.6830.0269
240.6070.0239
250.5310.0209
260.4550.0179
270.4170.0164
280.3780.0149
290.3430.0135
300.3050.012

Frequently asked questions

Are AWG and steel sheet gauge (MSG) the same standard?

No. AWG is a separate standard for wire diameter, and steel sheet gauge (Manufacturers' Standard Gage) is a different standard for sheet thickness. The same gauge number means a different actual size in each system.

Does this support galvanized steel or aluminum gauge?

No. Galvanized steel and aluminum have different thickness-per-gauge tables than plain steel, and we couldn't confidently verify reliable figures for them, so they're excluded here.

What formula does the AWG calculation use?

The standard formula d(mm) = 0.127 × 92^((36−AWG)/39), cross-checked against published AWG reference tables.

What if my measured thickness doesn't exactly match a standard gauge?

The size-to-gauge mode finds the nearest standard gauge number. Real stock may vary slightly from the nominal table value.

Why does a bigger gauge number mean a thinner wire or sheet?

Gauge numbering is inverted from what you might expect — it traces back to the number of drawing passes needed to produce the wire, so a higher gauge number means more passes and a thinner result. This is why 22 AWG wire is thinner than 10 AWG wire, and 20-gauge sheet metal is thinner than 10-gauge.

Does this tool show inches as well as millimeters?

Yes. Alongside the millimeter figure, the result also shows the equivalent size in inches, since American wire and sheet metal specs are often also given in inches.

Is AWG used for anything besides copper wire?

AWG is most commonly associated with copper and aluminum electrical wire, and that's what this tool's diameter figures reflect. It's a measure of cross-sectional diameter, independent of the conductor material, but different materials have their own conventions for how AWG is applied in practice.